I can use funky trees now so any walking mechanism will work, I would prefer bare bones of the contraption since I'd like to put something over it. I'll give you credit (and the person who made it.)
I can use funky trees now so any walking mechanism will work, I would prefer bare bones of the contraption since I'd like to put something over it. I'll give you credit (and the person who made it.)
@TheNightmareCompany
ok.
@PlanariaLab If you can, can you set the leg activation to Action-1 (as in the legs will not take any input unless action-1 is activated)? Other than that, it all looks good, and I am glad you told me this as well, this helps a lot, thanks.
@TheNightmareCompany
ok.
One more thing I would like to ask, is there anything in the list below that you want to change the Control axis or that you don't need?
.
Move (Forward) : Throttle
Move (Back) : Brake
Move (Side) : Yaw
Turn : Roll
Jump : LandgGear
Tilt Angle : Trim
Slope/stair switch (ankle angle) : AG7
Upright -> Crouch : VTOL(0~-1)
Walk -> Run : VTOL(0~1)
.
As you can see, when used at full capacity, all but one control axis is used, making it difficult to add weapon operations.
@PlanariaLab Okay, so right now I just have the bare bones of the top part. All I need you to do is install the legs to the bottom round fuselage. I'd like it if it was just the bare bones of it, but if not, then I can manage. I cannot make the rest until I have the legs so that I can tune everything right. Don't worry, I'll give you lots of the credit, because the legs are going to be what moves this. Thank you for your time and your help.
(Note: if you could get these done by early March, that would be great, because the deadline for this project is April 1st.)
Link to the creation
@PlanariaLab I'll try to keep the joints basic so that you can edit them easier, and thank you. (From what I understood of your post is that you will install the walking mechanism after I finish the product.)
I am expecting to be done with this by March, because I want to submit this by April 1st.
@TheNightmareCompany
Well, that is, things that are difficult to handle and things that have a lot of precautions (some errors may not be known yet).
They made in-kind requests without even listening to me, And they post works with mistakes (or don't work properly)
.
So let me incorporate and adjust it into your work
@PlanariaLab What happened? You don't have to tell me if you don't want to.
@TheNightmareCompany
Not uploaded. I can't go through the problematic ones, I've done it in the past with disastrous consequences.
@PlanariaLab Do you know were I can find the mechanism that was on that video, that you made?
@TheNightmareCompany
I understood approximately.
You will be able to do it.
You may need to have auxiliary jet for reaction rate and stability (can be done without jet, but it takes time to accelerate)
@PlanariaLab Any how I got to go, see you later, and thanks for checking this forum out, I need a par of legs for my capstone project.
@PlanariaLab Something like your mechanism in the Walking FT test for large Mechs video you made not to long ago.
@PlanariaLab I'm looking for between 16-20ft tall and 7-10ft wide. It can be bigger than that though.
@TheNightmareCompany
How much is the height?
ok
@PlanariaLab @Inuyasha8215 It just needs to have a humanoid walking style. It would be nice if it was big as well, but that is optional.
@PlanariaLab ah okay
@Inuyasha8215
I feel like I was released such things,
But, many of them are the same as those already commonly used.
And some of the mechanisms of some multifunctional things can also be downloaded. (in short, just removing the outside from the published doll)
So I think it is not necessary to release it again.
.
Well, if you have work hardware and control information, I may get on consultation.
Nagisa used to have posted one but it got deleted