Space Frame Chassis UCAD Tune
all credit goes to the original by @yeahboi
This is a spaceframe chassis bought by a UCAD employee, with his tuning ability he swap the engine with an Upgraded VS12 Centurion and make it into a drift chassis, the engine is a V12 from UCAD Centurion, a luxury performance car from UCAD that usually produce around 450hp (Toyota Century V12 is only rated at 200hp or less), but this upgraded engine now makes 750hp enough to get your car slidin around like a champ, the chassis is not terribly hard to drift, it just a little snappy
-Modification List-
•Engine Swap, from 200hp V8 > 750hp V12
•Camber Kit, -0.5° in the front and -1.5° in the back, can be increased
•Fuel tank placement, now put in the back for safety reason (the driver will be somewhat safe from burning fuel)
•Grip tuning to improve drifting stability, now the chassis is drift happy with a slight bit of Snapback Oversteer due to engine placement, counter steering is a must
Specifications
General Characteristics
- Predecessor Space Frame Performance Chassis
- Created On Android
- Wingspan 13.2ft (4.0m)
- Length 23.6ft (7.2m)
- Height 5.3ft (1.6m)
- Empty Weight 5,681lbs (2,577kg)
- Loaded Weight 5,947lbs (2,697kg)
Performance
- Wing Loading 439,839.3lbs/ft2 (2,147,483.6kg/m2)
- Wing Area 0.0ft2 (0.0m2)
- Drag Points 3862
Parts
- Number of Parts 234
- Control Surfaces 0
- Performance Cost 1,066
@Leftybar i think i can make double wishbone, i even have some working double wishbone suspension, unfortunately if you got high downforce on your car it would camber badly, but since the car you want to make is basically a brick i don't think this would be much of a problem, check out my Desert Runner Challenge, the car in the thumbnail is a 450hp AWD Monstrosity, all around Double Wishbone suspension, very snappy and need a lot of experience to drive, even myself having a hard time driving it
@WarshipWarshipTheDude Hey yo, you upvoted and gave feedback on my vehicle the IE84 Eleven, so I got a question, I was working n a 1988 dodge dakota sport 4x4, I was wondering if you could build the suspension of the truck, I was working on a chassis from before, the front suspension is a double wishbone independent suspension, and also with a CV axle because it's a 4x4 truck, I might build the frame and let you do the suspension so you can help out @Birdman9301, he needs all the help he can get for building my truck, plz ask me any questions if you like or need to help out, plz, thank you
@WarshipDude Lol.
@yeahboi its gone into oblivion because the engine is so goddamn big
@WarshipDude Oh, ok.
Actually, where did the transmission & transfer case go?
@yeahboi if it was a mid or rear engine i will use side, but this is a front engine RWD like the Toyota Century
@WarshipDude If its a mid-placed longitudal engine, try having 2, with one on each side of the engine.
@yeahboi yeah, the air filter is also the intake, is was too small but the space inside the hood (on the other car) is already small enough that i can't even make it bigger anymore
Oh, wait, nevermind. it has one. I just didnt see it.
Its epic.
Actually, if you want, you can make a subassembly out of the air filters on my version and use it for that engine.
@yeahboi the V12 is my own built for another car actually, the car was not yet completed, idk when i will complete it
I fookin' love it.
HOLY SHI-
@yeahboi