@Thunderbolt916 Thanks for your comment!
For the livery, maybe i will give it a new one, but i haven't watch the film now... I am trying to make fly-by wire these days, so i will update the control system. For the afterburners, it will activate when the throttle is over 98%, the thrust will increase but it doesn't have flames, which i will also update when i have time. And the HUD needs to be updated as well.
My thoughts when build this car:
First, maybe Simpleplanes can not tell the difference between static friction and dynamic friction, and static friction is always greater than dynamic friction when pressing force and the contact surfaces are the same. Just like my Supra, when I was tuning the power of the engine, I found that in some case when the power is a little high(just 600 hp), the wheels slip against the ground(you can hear that sound) even if it has a initial speed of 100 km/h which never happens in real life. (This also affects the airplane when touching down in crosswinds)
Second, the forward friction and the sideways friction should not be divided. Once the tire began to slip, the friction in all directions will drop.
Third, as you have explained above, the friction should increase as the pressing force increases. I think the things can be adjusted are the dynamic friction coefficient and the the ratio between the max static friction and the pressing force, which can be explained by changing the contact surface.
Above are my opinions. Mention me if I made some mistake.
@ShootsPlanes ok, your suggestion will be taken but i will be inactive after some days. I will make it some time later(maybe a very long period of time)
@Thunderbolt916 Thanks for your comment!
+1For the livery, maybe i will give it a new one, but i haven't watch the film now... I am trying to make fly-by wire these days, so i will update the control system. For the afterburners, it will activate when the throttle is over 98%, the thrust will increase but it doesn't have flames, which i will also update when i have time. And the HUD needs to be updated as well.
I removed the old post because it had too many bugs. You can try this
+1@MrShenanigans2020 yes maybe
+1元宵节快乐~
+1@donkski Maybe friction. I don't konw...
+1And the new wheels look definitely better
My thoughts when build this car:
First, maybe Simpleplanes can not tell the difference between static friction and dynamic friction, and static friction is always greater than dynamic friction when pressing force and the contact surfaces are the same. Just like my Supra, when I was tuning the power of the engine, I found that in some case when the power is a little high(just 600 hp), the wheels slip against the ground(you can hear that sound) even if it has a initial speed of 100 km/h which never happens in real life. (This also affects the airplane when touching down in crosswinds)
Second, the forward friction and the sideways friction should not be divided. Once the tire began to slip, the friction in all directions will drop.
Third, as you have explained above, the friction should increase as the pressing force increases. I think the things can be adjusted are the dynamic friction coefficient and the the ratio between the max static friction and the pressing force, which can be explained by changing the contact surface.
Above are my opinions. Mention me if I made some mistake.
+1@KendJello 到时候会安排，我也超喜欢RX-7的 :)
+1@Haytham115 @123Manbanana it is not custom, but the tyre after updating
+1if you are not on your PC, then download this
@PLNE I know the flag was wrong...
+1@BassemT90
+1@PLNE
@Minhdead2205
@JuanNotAnAlt
+1@ShootsPlanes
@BeastHunter
@Misaka7856 到时候会发B站上
+1@XAircraftManufacturer
+1@BassemT90
+1@PLNE
@Minhdead2205
@JuanNotAnAlt
+1@ShootsPlanes
@BeastHunter
@Xuwenze 差不多
+1@wfy312 记得，它飞控有点问题还没改。。。
+1@R3N13L Uhh... i don't know then. You can try to reduce the ranges of the pistons(they are inside the floor)
+1@R3N13L Well it is my fault. The switch on the doors are not disabled aircraft collisions.
+1@JuanNotAnAlt The FMS panel is yours:)
+1@MrShenanigans I am not sure actually.
+1@JuanNotAnAlt thanks:)
+1@JuanNotAnAlt Great, maybe i will use it on my MS-21:)
+1这种方法应该会让我的MS-21零件少很多
+1@JuanNotAnAlt Mid-Autumn holiday for only one day...
+1@JuanNotAnAlt and summer and winter vacations after i finished my homework.
+1@JuanNotAnAlt maybe school IT class...
+1@JuanNotAnAlt just Saturday afternoon and Sunday morning.
+1@JuanNotAnAlt once a week bro
+1@PSsyalperdna I won't forget this community and all of you guys!
+1@JuanNotAnAlt sad...
+1@LITVYAK013INDUSTRIES i used 4 gyroscopes to control it, they are in front of the rear rotor.
+1happy birthday:)
+1nb👍🏻
+1@Shippy456 Girls und Panzer
+1@JuanNotAnAlt i am sad too.
+1@ShootsPlanes ok, your suggestion will be taken but i will be inactive after some days. I will make it some time later(maybe a very long period of time)
+1@Xuwenze
+1@realSavageMan
I tagged all of you who upvoted or commented below my teaser because i think you are interested in this:)
+1@JuanNotAnAlt yeah
+1hey i am late again:)
+1that is excellent
+1@JuanNotAnAlt Nice
+1@Skykid028 ok
+1T
+1Hoof-shaped magnet)
+1@TheMaus
+1@PewDewEwwPew
+1@TatsuTheOtaku
@ToxicAviAviation
@Strikercritsilver
+1@BMilan
@TheSolarFlare
@JuanNotAnAlt
+1@BryanO5
@Strikercritsilver