This is an engine teaser :)
I made my first "detailed" engine for the upcoming W330-500 since the engine that is currently on the plane is worth a total of around 500+ parts. The new engine i made has only 60 parts. The higher part count is reserved for PC user and the lower part count will be the one made public because I want to allow both Mobile and PC users to enjoy the same build.
Name not revealed yet
Here is the engine:
@Wallaby ._.
@Horsepower yes now i know lol
@STUKAWOLF87 UMMMMMMMMMMMMMMMMMMM
Trent 1000
Did you know; a GE90-115b turbofan engine can generate an equivalent of over 100,000 mechanical horsepower? Now you know.
That sure is one very smooth engine you got there. It looks almost exactly like the GEnx and Rolls-Royce Trent 1000 engines used on the Boeing 787 if you asked me.
SimplePlanes
Profile image
Not a plane teaser
2,022 WingworksDesignCo 7 hours ago
This is an engine teaser :)
I made my first "detailed" engine for the upcoming W330-500 since the engine that is currently on the plane is worth a total of around 500+ parts. The new engine i made has only 60 parts. The higher part count is reserved for PC user and the lower part count will be the one made public because I want to allow both Mobile and PC users to enjoy the same build.
Name not revealed yet
Here is the engine:
Teaser
8 Comments
Profile image
Profile image
2,022 WingworksDesignCo
also use smoothing, smoothing helps yes
38 minutes ago
Profile image
2,022 WingworksDesignCo
wait i didnt even show the slant lol
39 minutes ago
Profile image
2,022 WingworksDesignCo
@PlanePlaneThe66373637 um its mostly changing the width and the height bit by bit, if its about the slant, I used finetuner to angle it forward a bit then reconnected it so that the front is connected to the top instead of to each other so that i can fill in the gaps that are made by the angled piece. Then the part the fills the gap would connect to the part behind it which makes it smooth.
39 minutes ago
Profile image
9,601 PlanePlaneThe66373637
How you make the front smooth?
an hour ago
Profile image
2,022 WingworksDesignCo
@p0tato72 nom
3 hours ago
Profile image
1,050 p0tato72
Mmmmmmmmyes
+1 3 hours ago
Profile image
2,022 WingworksDesignCo
@PoggersPoggersTheMan myessss
3 hours ago
Profile image
5,048 PoggersPoggersTheMan
myes
+1 5 hours ago
10 Upvotes
25.5k PointlessWhyshouldi
48.6k AlienbeefyTheCheekiBreeki
2,183 natemomog
15.7k YourWife
35.7k MobileFriendly
2,289 Aldriech
5,048 PoggersPoggersTheMan
28.9k Ghostium
1,050 p0tato72
7,540 CrushburnHQ
© Copyright 2019. All Rights Reserved.
2:55:06 PM
Press Kit Rules Privacy Policy Contact
also use smoothing, smoothing helps yes
wait i didnt even show the slant lol
@PlanePlaneThe66373637 um its mostly changing the width and the height bit by bit, if its about the slant, I used finetuner to angle it forward a bit then reconnected it so that the front is connected to the top instead of to each other so that i can fill in the gaps that are made by the angled piece. Then the part the fills the gap would connect to the part behind it which makes it smooth.
How you make the front smooth?
@p0tato72 nom
Mmmmmmmmyes
@PoggersPoggersTheMan myessss