@An2k Yes. This was made with reference to an old radio-controlled car.
The single shock isn't effective against rolls, but I made it because I was curious about how it would run.
@Perceptualhudfg
Don't worry.
My work is published on the assumption that other people will modify it.
It's a little old work, but I hope you enjoy it.
@Sm10684
The Honda Gold Wing is a good motorcycle. But I wouldn't make it. Because it can be produced just by using the mechanism of cx500 as it is. Perhaps the next thing I'll make will be a test vehicle for motocross.
@YourAlly
Maybe it may be insufficient in direct stability. It has three measures.
1: Back the side traction of the wheel larger than the front wheel.
2: Reduce the center of gravity as low as possible.
3: Install a vertical stable wing.
@YourAlly
Thank you!
It is easy to stand up because it uses a gyro stabilizer, but the point is to prevent the gyro stabilizer from intervening in the pitch direction.
@BlitzIsAwesome101
This is a fairly old build. It is also made for checking the operation of the suspension. If you want to mount a car body, you should make a suspension that matches it.
@UchihaKidForSale I don't know what to say because there are many hints.
However, knowledge of dynamics and statics will definitely help in the production.
@ParziParziTheVal Thanks for your comment!
I would have to experiment a lot of time to implement that method.
This modification will be a slight change in the center of mass position and lift position.
@An2k
Thanks for your comment!
I don't know if this work was the first use of Funky Trees.
If you use the trim when taking off, it will be easier to do.
@cnorth12
Of course, I can make other designs with the same suspension.
But the cars you make will need the suspensions you make.
This is because the car body and suspension must be made in coordination with each other.
If you want a realistic suspension, I give one piece of advice. It is good to make sure that the shock absorber has no cutting or bending force.
@ThomasRoderick
Thank you for watching the work.
Recently, I learned that you can use functions for input. It will take trial and error for some time before it can be used successfully.
@pilotWFD Thank you!
I am glad that more people make good suspension vehicles.
I am poor at English, but I will answer as much as possible if there is any technical doubt.
@pilotWFD Thanks comment !
This car was made carefully for suspension geometry, aerodynamic balance, center of gravity balance.
Although the caster angle is set on the front wheel, I think that this method is a handy and effective technique.
@Danillo
In order to make it compact and lightweight, parts modified with XML are necessary.
There are people uploading those parts.
Even without the help of MOD, you can make an accurate geometric suspension. That is very important.
Чтобы сделать его компактным и легким, необходимы части, модифицированные с помощью XML.
Есть люди, загружающие эти части.
Даже без помощи MOD вы можете сделать точную геометрическую подвеску. Это очень важно.
@Danillo The procedure for making a suspension is
1. Understand the geometry of each type of suspension.
2. Make it once in large size.
3. Adjust the length and angle of the arm to achieve the desired performance.
4. Make it smaller.
Процедура изготовления подвески
1. Понять геометрию каждого типа подвески.
2. Сделайте это один раз в большом размере.
3. Отрегулируйте длину и угол наклона рычага для достижения желаемой производительности.
4. Сделайте это меньше.
@Destroyerz117 The spring is proportional to the force and the damper is proportional to the operating speed.
I prefer to make the damper stronger than the spring rate in off-road vehicles.
It slows the speed at which the lifted suspension returns.
@Th3Missil3 I'm testing the chassis, so I might remake it.
+1@TatsuTheOtaku That's right. But it's not a detailed replica.
+1@sapnupuas
Your comment is happy for me.thank you!
@ArabicboiYT
+1I don't make new things, so you are free to use this.
@An2k Yes. This was made with reference to an old radio-controlled car.
+2The single shock isn't effective against rolls, but I made it because I was curious about how it would run.
@ThomasRoderick Thank you !
+2@Perceptualhudfg
Don't worry.
My work is published on the assumption that other people will modify it.
It's a little old work, but I hope you enjoy it.
@ThomasRoderick
+1Thank you!
However, I may take a break from making motorcycles and make something else.
@Sm10684
The Honda Gold Wing is a good motorcycle. But I wouldn't make it. Because it can be produced just by using the mechanism of cx500 as it is. Perhaps the next thing I'll make will be a test vehicle for motocross.
Very great! Beautiful helmet, hands and FT are also good!
+3@MisterT
Hahaha. Unfortunately I'm definitely the one who made this bike. Feel free to modify it.
@Sm10684
+1Yeah! I am very interested in motocrossers.
@YourAlly
Maybe it may be insufficient in direct stability. It has three measures.
1: Back the side traction of the wheel larger than the front wheel.
2: Reduce the center of gravity as low as possible.
3: Install a vertical stable wing.
@YourAlly
+1Thank you!
It is easy to stand up because it uses a gyro stabilizer, but the point is to prevent the gyro stabilizer from intervening in the pitch direction.
@ThomasRoderick
+2Hi! I'm planning to make another motorcycle next time. It will make a cafe racer or a supersport bike.
@BlitzIsAwesome101
This is a fairly old build. It is also made for checking the operation of the suspension. If you want to mount a car body, you should make a suspension that matches it.
@An2k
+1Thank you.
I hope the front fork pullout limiter will become a universal technology.
@ThomasRoderick
+2Thank you!
The test run was fun and the upload was delayed :)
@An2k
+3Thank you.
If anything, I was more influenced by Polaris' RZR.
@UchihaKidForSale I don't know what to say because there are many hints.
However, knowledge of dynamics and statics will definitely help in the production.
Hi, that's a good mod.
@UchihaKidForSale of course. Feel free to modify it.
@MASTERDUMBO Did you perform a mirror copy? If you do that, the pitch cycle of the wings will break.
+1@Alta2809 That may be true.
+1But I haven't cared about my rank.
@ParziParziTheVal Thanks for your comment!
I would have to experiment a lot of time to implement that method.
This modification will be a slight change in the center of mass position and lift position.
@An2k
Thank you!
But in fact, the vibration is large due to insufficient adjustment.
I will publish the adjusted one in a week.
@BigBoy772
That's because Swallow is the model.
Swallow is called "Tsubame" in Japanese
@An2k
+1Thanks for your comment!
I don't know if this work was the first use of Funky Trees.
If you use the trim when taking off, it will be easier to do.
@ThomasRoderick Thank you ! ( ´∀｀)
+2@cnorth12
Of course, I can make other designs with the same suspension.
But the cars you make will need the suspensions you make.
This is because the car body and suspension must be made in coordination with each other.
If you want a realistic suspension, I give one piece of advice. It is good to make sure that the shock absorber has no cutting or bending force.
@ThomasRoderick
+1Thank you for watching the work.
Recently, I learned that you can use functions for input. It will take trial and error for some time before it can be used successfully.
@ThomasRoderick Thanks for your comment
+1see you next time.
@pilotWFD Thank you!
I am glad that more people make good suspension vehicles.
I am poor at English, but I will answer as much as possible if there is any technical doubt.
@pilotWFD Thanks comment !
+1This car was made carefully for suspension geometry, aerodynamic balance, center of gravity balance.
Although the caster angle is set on the front wheel, I think that this method is a handy and effective technique.
@Danillo
In order to make it compact and lightweight, parts modified with XML are necessary.
There are people uploading those parts.
Even without the help of MOD, you can make an accurate geometric suspension. That is very important.
Чтобы сделать его компактным и легким, необходимы части, модифицированные с помощью XML.
Есть люди, загружающие эти части.
Даже без помощи MOD вы можете сделать точную геометрическую подвеску. Это очень важно.
@Danillo The procedure for making a suspension is
1. Understand the geometry of each type of suspension.
2. Make it once in large size.
3. Adjust the length and angle of the arm to achieve the desired performance.
4. Make it smaller.
Процедура изготовления подвески
1. Понять геометрию каждого типа подвески.
2. Сделайте это один раз в большом размере.
3. Отрегулируйте длину и угол наклона рычага для достижения желаемой производительности.
4. Сделайте это меньше.
@Hayhayjam664 Thank you!
+1@weebabyseamus Thank you! I am very honored! "Simple Planes" is really fun!
@SelectAKey Thanks for your comment! "Warthog" is an interesting plan.
@Hyattorama Thank you! I am very honored!
+1@LiamW Thank you! I think that the design of the suspension to build the details is also a pleasure to make a suspension.
+1@LiamW Thank you for always seeing my work!
+1@The1Big1Finger1111 Thanks for your comment!
I feel that rigid axle type suspension is very difficult to operate correctly.
@Rub3n213 Thanks for your comment!
Behind it is a radiator. However, it seems that it was a little useless work. hahaha
@aircraftarsenal123 @flyingsteve88 Thank you! I am very happy!
+2@Destroyerz117 The spring is proportional to the force and the damper is proportional to the operating speed.
I prefer to make the damper stronger than the spring rate in off-road vehicles.
It slows the speed at which the lifted suspension returns.
@Caveman999 Thank you !
@Hayhayjam664 @marcox43 I am trying to make cars that are fun to run around. So I am honored to have your comments :D
+1@marcox43 @Potkuri Thank you for watching my car and enjoying it!
The mechanism to increase the degree of freedom of rolls is a very unique attempt! Great!